Wisconsin Parts Database Instructions and Discussion Team/Group > INDIANA
> Motors and tools
> Dental / medical /tuttnauer 2340M autoclave/ sterilizer
Dental / medical /tuttnauer 2340M autoclave/ sterilizer
Guidelines for Infection Control in Dental Health-Care Settings - 2003MMWR December 19, 2003 / 52(RR17); 1-61
1. Use mechanical, chemical, and biological monitors according to the manufacturer's instructions to ensure the effectiveness of the sterilization process (IB) (248,278,279).
2. Monitor each load with mechanical (e.g., time, temperature, and pressure) and chemical indicators (II) (243,248).
3. Place a chemical indicator on the inside of each package. If the internal indicator is not visible from the outside, also place an exterior chemical indicator on the package (II) (243,254,257).
4. Place items/packages correctly and loosely into the sterilizer so as not to impede penetration of the sterilant (IB) (243).
5. Do not use instrument packs if mechanical or chemical indicators indicate inadequate processing (IB) (243,247,248).
6. Monitor sterilizers at least weekly by using a biological indicator with a matching control (i.e., biological indicator and control from same lot number) (IB) (2,9,243,247,278,279).
7. Use a biological indicator for every sterilizer load that contains an implantable device. Verify results before using the implantable device, whenever possible (IB) (243,248).
American Dental Association (ADA)
Monitor sterilizers at least weekly with biological (spore) indicators.1 Check whether your state dental board has different requirements.
Consider using biological (spore) indicators daily if the sterilizer is used frequently (e.g., several loads per day). Daily monitoring allows for earlier discovery of equipment malfunctions or procedural errors.
A positive spore test result indicates that sterilization was incomplete. Maintain a log of spore test results. Check your state regulations to determine how long you need to keep spore testing records. Organization for Safety and Asepsis Procedures (OSAP)
Infection Control Guidelines: September, 1997
9. Sterilization Monitoring: The use and functioning of heat sterilizers should be biologically monitored at least weekly, or more often if the practice demands it, with appropriate spore tests. Place the spore strips or vials inside a pouch, bag, pack or cassette, and include this package as part of the normal load through a normal sterilizer cycle. Always use a control spore strip or vial (not heat processed but otherwise treated identically to the test strips or vials) with each spore test performed. Additionally, chemical indicators should be used on the inside of each package during every sterilizer load. Accurate records of sterilization monitoring must be maintained. A chemical indicator from inside each pack may be initialed and dated for each day of patient care and kept in a file. The weekly spore test for each heat sterilization unit may be kept in the same file. Biologically monitor whenever there is a change in packaging, following equipment repair; retest after failure and when training new employees. Association for the Advancement of Medical Instrumentation (AAMI)AAMI: Steam Sterilization and Sterility Assurance, 7.5.4 Test Frequency.
"Biological indicators must be used no less than weekly for each sterilizer and, preferably, should be used for each load. More frequent testing should be carried out on an as needed basis (I.E., after major sterilizer repairs, when evaluating sterilization of new products, when implantable or intravascular materials are sterilized, etc.)".
Association of Perioperative Registered Nurses (AORN)
Recommended Practices, Sterilization & Disinfection, 1987.
"For routine monitoring should be used weekly, and as needed; each load of implantables."
VA Manual G1, MP-2, 1985 and MP-2, Sub-chapter E, Change 159, June 22, 1983.
"Must be monitored no less than weekly, each load of implantables or intravascular materials, following major sterilizer repairs, new products or packaging material."
- Overheat cutoff prevents burnout of heating elements in case of insufficient water in the chamber.
Model Chamber Dimensions Overall Dimensions
2340M 5gal 9" x 18.5" 21.5" x 20" x 14.4"
Tuttnauer manual autoclaves set the standard for steam Sterilization. The Tuttnauer manual autoclave is designed to compliment any healthcare and laboratory facility. Our basic manual autoclave will satisfy all of your sterilization needs. Time tested reliability and durability are built into every Tuttnauer product.
