Wisconsin Parts Database Instructions and Discussion Team/Group > ILLINOIS
> Motors and tools
> Add
> Safety smv 72 red led lights complete with mounting kit
Safety smv 72 red led lights complete with mounting kit
Suggested Retail $109.99 for 72 RED LED SMV sign.
ITEM DESCRIPTION: Slow Moving Vehicle (S.M.V.) Safety Sign with 72 RED LED Lights & MOUNTING KIT. New A.S.A.E. S276.6 Sign Base. Good for Riding Mowers, ATV s, Garden Tractors, Farm Equipment, Trailers, Utility Vehicles, Go Karts, Trailers, or anywhere you would like to make your vehicle more visible to other approaching vehicles. Increase your safety by increasing your visibility. Super safe, alert drivers behind you. 12 volt DC 2 wire system. Easy to install. Complete Kit (WITH MOUMTING HARDWARE).
This sign will fit a variety of mowers, tractors (including John Deere, Kubota, New Holland, Sears Craftsman, Bobcat, and many others), farm equipment, ATV's, UTV's, Trailers, skid steers, Loaders, etc.
ITEM DESCRIPTION: Slow Moving Vehicle (S.M.V.) Sign with 72 RED LED Lights New A.S.A.E. S276.6 Sign Base. Good for Riding Mowers, ATV s, Garden Tractors, Farm Equipment, Trailers, Utility Vehicles, Go Karts, Trailers, or anywhere you would like to make your vehicle more visible for approaching vehicles. Increase your safety by increasing your visibility. 12 volt system. You will receive a sign like the one pictured. Each 24cm LED strip is individually tested when it is received. Each S.M.V. sign is tested after the lights have been attached to be sure all 3 LED strips work. The LED lights on the sign are then tested a 3rd time after the wiring has been completed. Each sign is 100% guaranteed to work. I have a 1 amp battery charger that easily lights these 72 LED Lights. I used AA batteries to light the sign in this picture.
- New official highly reflective S.M.V. Sign with 72 Red LED 12 volt lights that are wired into a 2-pole flat wire connector. The sign overall measures 14 top to bottom / 16 overall from side to side / The 3 long straight edges each measure 12 in length / The 3 short straight edges each measure 4 in length. Each LED strip contains 24 RED LED lights that measure 24cm in length (9.5 ). The sign backing is high impact plastic.
- 2 qty 4 Plastic zip ties to secure wire to your vehicle or trailer.
- Mounting Kit = Hardware mounting socket, spade mount, 2 nuts & bolts for sign bracket (on back of sign), 2 nuts and bolts for mount bracket (on back of your vehicle).
- 2 qty Red butt splice connectors 18 - 22 AWG. (If you prefer this type of connecter)
- 2 qty Blue wire splice connectors. 14 - 16 AWG (If you prefer this type of connector)
- 1 qty 5 of 2 wires attached to a 2-pole flat wire connector. This is used to connect the sign to your vehicle or trailer. You may cut this wire down to a shorter length if necessary. This wire will make it easy to disconnect the electric wire going to the sign if you need to remove the sign for any reason. The positive wire is marked. NOTE: The positive wire must be connected to a positive 12 volt wire on your vehicle or trailer AND the other wire must be properly grounded or THE LED LIGHTS WILL NOT WORK. If you are able to connect the positive wire and the negative wire correctly, the sign WILL WORK!
- You need to know how to do very basic wiring. 1 positive wire (+) and 1 negative (-) ground wire. This is a 12 volt DC system.
- You will need a pair of pliers or wire crimpers to attach the 5 wire to your vehicle or trailer.
- You may need a drill approximately two 5/16 holes to mount the sign. The sign has 2 holes pre cut. However, the center orange triangle covers the 2 holes. You can push a pencil or pen through the sign to expose the holes (push from the front of the sign through the hole to the back of the sign. It will prevent the highly reflective sticker from pealing up a bit when you attempt to open the 2 premade mounting holes.
- Use a 12 volt test light to identify the positive wire on your vehicle or trailer.
WHAT IS WRONG WITH IT? Nothing. Each sign is 100% new (never used) hand assembled in the U.S.A. The S.M.V. Sign has been purchased already assembled. The LED lights & wiring have been added by hand. Therefore there may be a very slight variation in each sign that is reflective of the individual hand assembly.
Everyone is welcome and encouraged to ask questions!
